Pololu MAX14870 Engine Driver

Overview

The MAX14870 from Maxim Integrated is a tiny H-bridge motor driver IC that can be used for bidirectional control of one brushed DC motor at 4.5 V to 36 V. It can supply up to about 1.7 A continuously and can tolerate peak currents up to 2.5 A for a few seconds, making it a good choice for small motors that run on a wide range of voltages. The MAX14870 is a great IC, but its small surface-mount package makes it difficult for the typical student or hobbyist to use; breakout board makes it easy to use with standard solderless breadboards and 0.1" perfboards. Since this board is a carrier for the MAX14870, we recommend careful reading of the MAX14870 datasheet (492k pdf). The board ships populated with SMD components, including the MAX14870 and a reverse battery protection circuit.

We also carry a dual MAX14870 motor driver shield that makes it easy to incorporate this great driver into an Arduino project.

For similar motor drivers that operate at lower voltages, consider our BD65496MUV and DRV8838 motor driver carriers.

MAX14870 Single Brushed DC Motor Driver Carrier, bottom view with dimensions.

Features

• Single-channel H-bridge motor driver with shoot-through protection and internal free-wheeling diodes (can drive one DC motor)

• Motor supply voltage: 4.5 V to 36 V

• Output current: up to 1.7 A continuous (2.5 A peak)

• No separate logic supply needed; inputs are 3V- and 5V-compatible

• Simple two-pin DIR/PWM interface (one pin controls direction and another controls speed)

• Under-voltage lockout and protection against over-current/short-circuit and over-temperature

• Carrier board adds reverse-voltage protection

• Active-low fault output indicates over-current or over-temperature condition

• Surface-mount resistor can optionally be added to enable automatic current limiting

• Compact size (0.6"x0.5")

Using the motor driver

Minimal wiring diagram for connecting a microcontroller to a MAX14870 Single Brushed DC Motor Driver Carrier.

Motor and power connections are made on one side of the board and control connections are made on the other. The driver requires an operating voltage between 4.5 V and 36 V to be supplied to the reverse-protected power input, VIN. The VM pin provides convenient access to the reverse-protected supply voltage.

The MAX14870 offers a simple two-pin DIR/PWM control interface, where the DIR pin determines the motor direction and the PWM pin can be supplied with a PWM signal to control the motor speed. The PWM control input is pulled low on the carrier board through a 100 kΩ pull-down resistor. When the PWM pin is low, the motor outputs are both shorted to ground, which results in dynamic braking of a connected motor.

The EN pin can be driven high to turn off motor outputs, which is useful if you want to let the motor coast. The EN pin is pulled low through a 100 kΩ pull-down resistor on the carrier board so that the driver is enabled by default.

The following simplified truth table shows how the driver operates:

Pinout

Optional current limiting

The MAX14870 IC features a SNS input that can be used for optional automatic current limiting. By default, this input is connected to ground on the carrier board, which bypasses the current regulation feature. To enable current limiting, you must first cut the trace between the two unpopulated 1206 resistor pads on the top side of the carrier board:

Then, you will need to add your own appropriate surface-mount 1206 resistor to these pads. An example of this is shown below:

The driver tries to keep the voltage on the SNS pin from exceeding 100 mV, so for example, a 100 mΩ resistor limits the current to 1 A and a 200 mΩ resistor limits it to 0.5 A. For more information on current limiting, see the MAX14870 datasheet (492k pdf).

Real-world power dissipation considerations

The MAX14870 datasheet recommends a maximum continuous current of 2.5 A. However, the chip by itself will typically overheat at lower currents. In our tests, we found that the chip was able to deliver 2.5 A for only a few seconds before the chip’s thermal protection kicked in and disabled the motor outputs; a continuous current of 1.7 A was sustainable for many minutes without triggering a thermal shutdown.

The actual current you can deliver will depend on how well you can keep the motor driver cool. The carrier’s printed circuit board is designed to help with this by drawing heat out of the motor driver chip. Our tests were conducted at 100% duty cycle with no forced air flow; PWMing the motor will introduce additional heating proportional to the frequency.

This product can get hot enough to burn you long before the chip overheats. Take care when handling this product and other components connected to it.

Schematic

MAX14870 single brushed DC motor driver carrier schematic diagram.

This schematic is also available as a downloadable pdf (138k pdf).

Specifications

Dimensions

General specifications

Notes:

1 Without included hardware.
2 Typical results with VIN=12 V and 100% duty cycle at room temperature.

Don't delay, buy today.

Add to cart now!