Dupa plasarea solicitării de comandă, in sectiunea Istoric puteti vedea cate solicitări de comandă mai avem de procesat inaintea dumneavoastra
Program de lucru: Luni - Vineri 9:00 - 18:00, pauza 13:00 - 14:00.
Se efectueaza lucrari de mentenanta la site si pot aparea erori. In cazul in care intampinati erori va rugam sa reincercati mai tarziu.
Ridicarea personala este disponibila pentru comenzile achitate in avans. Se pot ridica dupa ce sunt pregatite.
No products
View larger
FormFutura StoneFil Filament - Terracotta, 2.85 mm, 50 g
8718924478523
New product
StoneFil is a PLA-based filament that is based on our modified and easy-to-print EasyFil PLA compound and is gravimetrically filled with 50% of powdered stone.
See Description for more details about the product.
Don't delay, buy today. Add to cart now!
1 Item
Warning: Last items in stock!
- Write a review
- Remove this product from my favorite's list.
- Add this product to my list of favorites.
More info
Description
This high "stone filling" has resulted in a 3D printer filament with remarkable aesthetic features and a significant higher material density up to 37% higher than "normal" PLA. StoneFil is an easy-to-print 3D printer filament and printed objects have an extremely matte stone-like finish with unique natural gradient color linings resulting in an exceptional chromatic spectrum per print. Every StoneFil printed object will have its own identity and unique gradient color shading.
Unique features
- Easy to print
- 50% gravimetric powdered stone filling
- ±37% heavier than "normal" PLA
- Matte and rough stone-like finish
- Unique natural/organic gradient color linings
- Every print has its unique natural stone gradient color shading
General printing guidelines *
| Nozzle size: ≥ 0.4mm | Layer height: ≥ 0.15mm | Flow rate: ± 110% |
| Print temp: ± 215 - 240oC | Print speed: High / Medium | Retraction: Yes ± 5mm |
| Heat bed: ± 0 - 60oC | Fan speed: 50-100% | Experience level: Beginner |
*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There is a lot of different type of printers, hot-ends, and printer offset that it is extremely difficult to give an overall one-size-fits-all setting.
Abrasiveness
StoneFil has a very high filling with stone powders and therefore the filament can have a slightly more abrasive effect on brass nozzles than unfilled filaments.
Filament length
| p: 1.70 g/cc | 50 gr coil | 0.5 Kg spool |
| Ø 1.75mm | ± 12.2m | ± 122m |
| Ø 2.85mm | ± 4.6m | ± 46m |
Nozzle cleaning
When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.
| Properties | Typical value | Test Method | Test condition |
|---|---|---|---|
| Physical | |||
| Specific gravity | 1.7 g/cc | ISO 1183 | - |
| Melt flow rate | 94 g/10min | ISO 1133 | 210oC/2.16Kg |
| Water absorption | - | - | - |
| Moisture absorption | - | - | - |
| Mechanical | |||
| Impact strength | 2.9 KJ/m2 | ISO 179 | Charpy Notched @23oC (73oF) |
| Tensile strength | 38.0 Mpa | ISO 527 | @Yield 50mm/min (2 inch/min) |
| Tensile modulus | 4760 Mpa | ISO 527 | - |
| Elongation at break | 33% | ISO 527 | @ Break 50mm/min (2 inch/min) |
| Flexural strength | - | - | - |
| Flexural modulus | - | - | - |
| Hardness | - | - | - |
| Thermal | |||
| Print temperature | ± 190 - 240oC | - | - |
| Melting temperature | ± 77 - 153oC | ISO 11357 | - |
| Viscat softening temp. | ± 57oC | ISO 306 | VST/A/50 (50oC/h, 10N) |
| Optical | |||
| Haze | - | - | - |
| Transmittance | - | - | - |
| Gloss | - | - | - |